| Command | Description |
| SECT_PRG_MAIN_O | O: Program number (main program) |
| SECT_PRG_MAIN_N | N: Sequence number (main program) |
| SECT_PRG_MAIN_B | B: Block number (main program) |
| SECT_PRG_SUB_O | O: Program number (subprogram) |
| SECT_PRG_SUB_N | N: Sequence number (subprogram) |
| SECT_PRG_SUB_B | B: Block number (subprogram) |
| SECT_PRG_NEST | Subprogram call level |
| SECT_PRG_MAIN_O_DEV | Search completed main program storage destination |
| SECT_PRG_SUB_O_DEV | Search completed subprogram storage location |
| SECT_G_GROUP1 | G command value (group 1 command) |
| SECT_G_GROUP2 | G command value (Group 2 command) |
| SECT_G_GROUP3 | G command value (Group 3 command) |
| SECT_G_GROUP4 | G command value (group 4 command) |
| SECT_G_GROUP5 | G command value (group 5 command) |
| SECT_G_GROUP6 | G command value (group 6 command) |
| SECT_G_GROUP7 | G command value (group 7 command) |
| SECT_G_GROUP8 | G command value (group 8 command) |
| SECT_G_GROUP9 | G command value (group 9 directive) |
| SECT_G_GROUP10 | G command value (group 10 command) |
| SECT_G_GROUP11 | G command value (group 11 command) |
| SECT_G_GROUP12 | G command value (group 12 command) |
| SECT_G_GROUP13 | G command value (group 13 command) |
| SECT_G_GROUP14 | G command value (group 14 command) |
| SECT_G_GROUP15 | G command value (group 15 command) |
| SECT_G_GROUP16 | G command value (group 16 command) |
| SECT_G_GROUP17 | G command value (group 17 command) |
| SECT_G_GROUP18 | G command value (group 18 command) |
| SECT_G_GROUP19 | G command value (group 19 directive) |
| SECT_G_GROUP20 | G command value (group 20 command) |
| SECT_G_GROUP21 | G command value (group 21 command) |
| SECT_G_GROUP22 | G command value (group 22 command) |
| SECT_G_GROUP23 | G command value (group 23 command) |
| SECT_G_GROUP24 | G command value (group 24 command) |
| SECT_G_GROUP25 | G command value (group 25 command) |
| SECT_G_GROUP26 | G command value (group 26 command) |
| SECT_G_GROUP27 | G command value (group 27 directive) |
| SECT_G_GROUP28 | G command value (group 28 command) |
| SECT_G_GROUP29 | G command value (group 29 command) |
| SECT_G_GROUP30 | G command value (group 30 command) |
| SECT_FA | FA: F command feed speed |
| SECT_FS | FS: Synchronous feed speed |
| SECT_FC | Fc: Automatic effective feedrate |
| SECT_FE | FE: Screw lead |
| SECT_DWELL | Dwell remaining time |
| SECT_SINGLE_B_STS | Invalid state: single block |
| SECT_MSTFIN_STS | Invalid state: MST complete |
| SECT_FEEDHOLD_STS | Invalid state: feed hold |
| SECT_OVERRIDE_STS | Invalid state: Override |
| SECT_IGSACT_STS | Invalid state: Exact |
| SECT_ACT_MAIN_COMMENT | Program comment |
| SECT_RUN_STATUS | Operating condition |
| SECT_RUN_MODE | Operation mode |
| SECT_SUB_SYSTEM_INFO1 | Sub-line information 1 |
| SECT_SUB_SYSTEM_INFO2 | Sub-line information 2 |
| SECT_CURRENT_PROG | Running program (type 1) |
| SECT_ALARM_INFO_COM | Alarm information (common to the system) |
| SECT_ALARM_INFO_SYS | Alarm information (system independent) |
| SECT_ACT_REAL_P_NO | Running program number |
| SECT_ACT_REAL_B_NO | Running block number |
| SECT_PLC_MESSAGE | PLC message information |
| SECT_PRG_MAIN_O_MEM | O: Search program number of memory operation |
| SECT_TOOL_COMPENSATION1 | Tool correction number 1 |
| SECT_TOOL_COMPENSATION2 | Tool correction number 2 |
| SECT_UPDATE_AXIS_INFO | Axis information update counter |
| SECT_CURRENT_PROG2 | Running program (type 2) |
| SECT_CURRENT_PROG3 | Running program (type 3) |
| SECT_CURRENT_PROG4 | Running program (type 4) |
| SECT_ALARM_CHG_CNT | Alarm message update information |
| SECT_PRG_TREE_O | Program tree information O: Program number |
| SECT_PRG_TREE_N | Program tree information N: Sequence number |
| SECT_PRG_TREE_B | Program tree information B: Block number |
| SECT_PRG_TREE_L | Program tree information L: Loop count |
| SECT_PRG_TREE_MODE | Program tree information operation mode |
| SECT_MDI_STATUS | MDI setting status |
